| Item type |
学術雑誌論文 / Journal Article(1) |
| 公開日 |
2015-12-02 |
| タイトル |
|
|
タイトル |
Heat Transfer Characteristics of Work Fluid Including Phase Change Material That Flow into Heating Surface from Narrow Path |
|
言語 |
en |
| 言語 |
|
|
言語 |
eng |
| キーワード |
|
|
主題Scheme |
Other |
|
主題 |
Phase Change Material |
| キーワード |
|
|
主題Scheme |
Other |
|
主題 |
Heat Transfer |
| キーワード |
|
|
主題Scheme |
Other |
|
主題 |
Low Temperature Difference |
| キーワード |
|
|
主題Scheme |
Other |
|
主題 |
Working Fluid |
| 資源タイプ |
|
|
資源 |
http://purl.org/coar/resource_type/c_6501 |
|
タイプ |
journal article |
| アクセス権 |
|
|
アクセス権URI |
open access |
| 著者 |
Morita, Shin-Ichi
Hayamizu, Yasutaka
Yamada, Takanobu
Horibe, Akihiko
Haruki, Naoto
Setoguchi, Toshiaki
Adachi, Kazuma
|
| 著者別名 |
|
|
|
識別子Scheme |
WEKO |
|
|
識別子 |
44816 |
|
|
識別子Scheme |
KAKEN |
|
|
識別子URI |
https://nrid.nii.ac.jp/ja/nrid/1000090174721 |
|
|
識別子 |
90174721 |
|
|
姓名 |
山田, 貴延 |
|
|
言語 |
ja |
| 抄録 |
|
|
内容記述タイプ |
Abstract |
|
内容記述 |
Use of the low temperature (less than 100˚C) energy contributes to effective use of heat resources. The cost recovery by power generation is difficult by using an existing system (the binary cycle or the thermoelectric conversion element), because the initial investment is large. The final purpose of this research is development of the low temperature difference drive engine supposing use in a hot-springs resort as a power source for electric power generation. In order that a traveler may look at and delight a motion of an engine, it is made to drive at low-speed number of rotations. An engine cycle of this study is aimed at the development of Stirling cycle engine which can maintain high efficiency in small size. This kind of engine has simple structure; it brings low cost, and it is easy to perform maintenance. However, it is difficult to obtain enough output by this type of engine, because of its low temperature difference. This paper deals with the heat transfer characteristic that the working fluid including a phase change material flows into the heating surface from the narrow path. In order to increase the amount of the heat transmission, Diethylether is added to the working fluid. Diethylether is selected as a phase change material (PCM) that has the boiling point which exists between the heat source of high temperature and low temperature. The parameters of the experiment are additive amount of PCM, rotational speed of the displacer piston and temperature of heat transfer surface. It is shown that it is possible to make exchange of heat amount increase by adding phase change material. The result of this research shows the optimal condition of the difference in temperature in heat processing, number of revolutions, and addition concentration of PCM. |
| 書誌情報 |
Open Journal of Fluid Dynamics
巻 4,
p. 454-462,
発行日 2014-12
|
| DOI |
|
|
|
識別子タイプ |
DOI |
|
|
関連識別子 |
https://doi.org/10.4236/ojfd.2014.45036 |
| 権利 |
|
|
権利情報 |
Copyright c 2014 by authors and Scientific Research Publishing Inc.This work is licensed under the Creative Commons Attribution International License (CC BY).http://creativecommons.org/licenses/by/4.0/ |
| 出版者 |
|
|
出版者 |
Scientific Research Publishing |
| 著者版フラグ |
|
|
言語 |
en |
|
値 |
publisher |
| 出版タイプ |
|
|
出版タイプ |
VoR |
|
出版タイプResource |
http://purl.org/coar/version/c_970fb48d4fbd8a85 |
2014.12_Heat Transfer Characteristics of Work Fluid Including Phase Change Material That Flow into Heating Surface from Narrow Path .pdf (2.8 MB)
